quattroworld


allroad
All messages | Search Forums | Return to allroad
RmcQ's original AW oil change how to w/ photo's restored
Posted by: - GT Style - (1280) on 2009-10-09 19:46:59

Share | Report
Found this how to w/ dead photo links, added the photo's back in for folks searching for oil change how to's


RMcQ procedure - THE ALLROAD OIL CHANGE - detailed instructions and many pics

--------------------------------------------------------------------------------

To redeem myself for recent non-value posts and to make up with my friends allroadguy and Neb, I took some time to document my Thanksgiving weekend oil change. There seems to be some interest on the board since the dealer interval of 10K miles is too long. I perform an in between oil change to reduce mine to a 5K mile interval.

The allroad has the most involved oil change procedure of any vehicle I have ever done due to the belly pan. So to give encouragement or direction to someone who hasn't tried it yet, here is THE ALLROAD OIL CHANGE...

TOOLS REQUIRED (some substituions are obviously possible. This is just what I used.)



For belly pan:

- Standard screw driver
- Stubby standard screw driver
- 8mm allen driver, 3/8" drive
- 3/8" drive ratchet
- 3/8" drive extension
- T30 Torx driver

For everything else:

- Ramps (not pictured above, see below)
- Oil drain collection pan (not pictured)
- Funnel
- Filter wrench or strap wrench
- 19mm box wrench
- Shop towels
- Appropriate storage/transport container for used oil (not picured)

MY PROCEDURE (again, some variations are possible. This is not necessarily the perfect way - its just my way. Constructive feedback encouraged.)

1. Prepare Vehicle

Warm the engine to suspend contaminants and to encourage a thorough drain. Raise the vehicle to level 4 and and park the car on ramps. FWIW - I have Rhino Ramps that are great because they are plastic and can be stored outside with no ill effects.



2. Remove Belly Pan

For those that have not crawled under their car, this is what the belly pan looks like in situ. Unfortunately I did not capture all the fasteners in this photo, but it gives you an idea. There are actually two (2) panels that make up the overall belly pan system. For an oil change it is not necessary to drop the rear one. Once all the fasteners are out of the front one, you can tilt it down a bit and slide it rearward to get it out. Leave the other panel in place. You can see the seam that delineates the two panels just behind the 3 indicated quick lock screws at the bottom of this photo.



Shot of 1st and 2nd pan overlap, from the side:



The three (3) Torx fasteners are all the way at the front, attaching the belly pan to the lower front bumper.

The T30 Torx fastener:



The Allen bolts are just a little further back. They are the most substantial fastener in the belly pan, though there are only two (2) of them.



The six (6) quick lock screws are all around the perimeter. They are all vertically into the belly pan. They require a simple turn to remove.



What you can not see in the above belly pan picture are the four (4) plastic quick connect screws that are in the fender well. These are oriented horizontally and also require a turn to extract. There is little space to access these due to the tire being in the way. This is where I used the short, stubby screwdriver to access two (2) per side.



Detail of fender well fastener:



If you get them all out, you will end up with a collection like this:



You can then tilt the rear of the belly pan down and away from the 2nd belly pan. Slide the thing rearward to slip it out from under the front bumper and it will drop right out.



3. Drain Oil

Now we get to the easy part just like any other car. Position your drain receptacle below the drain plug. Using a 19mm box wrench remove the drain plug. Careful - the oil may be hot!



4. Remove Filter

I used a strap wrench on the filter to loosen it a bit.



Make sure you drain receptacle is in place because after backing it out a turn or so the oil will start to drain out. I leave it like this for a few moments to let most of the oil drain out so I don't get it all the way up to my elbow when I remove the filter.



5. Replace Filter

After the obligatory wetting of the rubber gasket with some of the oil, screw the new filter on and tighten until very snug. I usually just do it as tight as I can get with my bare hands - no strap wrench at all when tightening.

6. Replace Drain Plug

Tighten this back up with your box wrench. I'm not sure what the exact torque spec is, but my my highly calibrated forearm torque wrench says not to over do it. Just a little tight is fine.

7. Replace Belly Pan

Drag this big thing back under the car with you and first position the front of it into the front bumper. Be sure that in the fender well area the belly pan goes behind the fender liner as you tilt the pan up in the rear to get it back into its original position. Replace all the fasteners that you removed. You might have to fiddle with some of the quick lock fasteners because the backing part could get out of position.

8. Fill with oil

I use a small funnel the locks in place and allows me to stand the Mobil 1 oil bottles up in it to get every drop.



You should check it while you top it up, but my experience is that 6 to 6.5 quarts is what you will need.

Replace the filler cap and you're done. Put your tools away for the next 10,000 miles.
Thread:
post follow up

You must be registered and logged in to post. Please select an option:

Login with existing account
Create a new account

All messages | Search Forums | Return to allroad