quattroworld.com Forums: Normal FP behavior = ignore. You need 12v at ECU 35 and Coil positive side

All messages | Search Forums | Return to 5000/100/200

Normal FP behavior = ignore. You need 12v at ECU 35 and Coil positive side
Posted by: qshipq (4418) on 2017-02-15 17:38:18 In Reply to: Fuel pump doing funky things. posted by Hoosierman on 2017-02-15 17:07:55	Share \| Report

I suspect you have a bad ignition switch

SJ

Thread:

Well I've gone through all grounds again. - Hoosierman 2017-02-14 20:06:04 (427 views)
- Did you end up with any solution? - afterthought 2017-03-06 21:11:43 (271 views)
  - Ah nevermind , saw post above. Loose ground - afterthought 2017-03-06 21:23:47 (380 views)
- ignition coil pickup window not aligned at TDC - Hoosierman 2017-02-14 23:15:56 (472 views)
  - uhhh what's the history of that distributor you've got there? - quattroooooooo 2017-02-15 14:15:36 (400 views)
    - it is the correct distributor IME - qshipq 2017-02-15 14:55:11 (392 views)
    - This is what the sensor should look like - quattroooooooo 2017-02-15 14:36:22 (472 views)
      - Way off base here!   -  qshipq  2017-02-15 15:37:17 (411 views)
        
        Yeahhh I'm getting pretty bad CRS lately  -  quattroooooooo  2017-02-15 18:28:25 (374 views)
        
        Found this in a study program today (timing sensors)   -  quattroooooooo  2017-02-16 15:50:03 (326 views)
        
        The Hall is only used for starting, correct  -  qshipq  2017-02-17 10:06:29 (283 views)
        
        I wonder then...  -  quattroooooooo  2017-02-17 19:06:30 (279 views)
      - look carefully at his pic... - qshipq 2017-02-15 14:59:58 (425 views)
  - Forget fuel, you need spark - qshipq 2017-02-14 23:36:02 (408 views)
    - Well I am getting a code now. - Hoosierman 2017-02-15 07:20:43 (372 views)
      - Physically swap it with the rpm sensor they are interchangeable  -  qshipq  2017-02-15 09:47:51 (395 views)
        
        I have a couple extra sensors so I will try swapping them out tonight. As well as rotate distributor  -  Hoosierman  2017-02-15 11:15:42 (374 views)
        
        Rotate distributor first!  -  qshipq  2017-02-15 13:47:51 (421 views)
        
        The code changed to a 2111 with the sensors swapped.  -  Hoosierman  2017-02-15 16:09:56 (361 views)
        
        Did you get all the codes or just the latest code?  -  qshipq  2017-02-15 16:22:14 (368 views)
        
        Well switched it out with a good sensor...  -  Hoosierman  2017-02-15 16:39:35 (365 views)
        
        Did you move distributor while cranking?   -  qshipq  2017-02-15 17:07:57 (340 views)
        
        And that's the only code, no others follow after reinserting fuse   -  Hoosierman  2017-02-15 16:43:14 (396 views)
        
        Only getting 9.5 volts at between ECU pins 35 and 18. Battery is reading 12v and it's hooked up to  -  Hoosierman  2017-02-15 16:57:32 (392 views)
        
        try 35 and a body ground  -  qshipq  2017-02-15 17:24:23 (393 views)
        
        Also make sure you have 12v at fuse block   -  qshipq  2017-02-15 17:45:52 (367 views)
        
        Fuel pump doing funky things.  -  Hoosierman  2017-02-15 17:07:55 (341 views)
        
        Normal FP behavior = ignore. You need 12v at ECU 35 and Coil positive side  -  qshipq  2017-02-15 17:38:18 (365 views)
        
        It's not the hall sender in the distributor that needs to be 'aligned', as such..   -  TyloPuP.. katMAN  2017-02-15 11:36:01 (600 views)
        
        That's what I thought  -  Hoosierman  2017-02-15 12:47:07 (362 views)
        
        Ok then..  -  TyloPuP.. katMAN  2017-02-15 13:26:25 (371 views)

You must be registered and logged in to post. Please select an option:

All messages | Search Forums | Return to 5000/100/200

Copyright © VerticalScope Inc. All rights reserved.

quattroworld.com is an independent Audi enthusiast website owned and operated by VerticalScope Inc. Content on quattroworld.com is generated by its users. quattroworld.com is not in any way affiliated with Audi AG.